mirror of
https://github.com/tildearrow/furnace.git
synced 2024-11-24 05:25:12 +00:00
70 lines
4 KiB
Markdown
70 lines
4 KiB
Markdown
# OPL FM synthesis instrument editor
|
||
|
||
The OPL FM editor is divided into 7 tabs:
|
||
|
||
- **FM**: for controlling the basic parameters of FM sound source.
|
||
- **Macros (FM)**: for macros controlling algorithm and feedback
|
||
- **Macros (OP1)**: for macros controlling FM parameters of operator 1
|
||
- **Macros (OP2)**: for macros controlling FM parameters of operator 2
|
||
- **Macros (OP3)**: for macros controlling FM parameters of operator 3 (Warning: only when 4-op flag is set, only on OPL3!)
|
||
- **Macros (OP4)**: for macros controlling FM parameters of operator 4 (Warning: only when 4-op flag is set, only on OPL3!)
|
||
- **Macros**: for miscellaneous macros controlling volume, arpeggio, and YMF262 panning.
|
||
|
||
## FM
|
||
|
||
The OPL synthesizers are nominally two-operator (OPL3 supports limited 4-operator mode), meaning it takes two oscillators to produce a single sound.
|
||
|
||
These apply to the instrument as a whole:
|
||
- **Feedback (FB)**: Determines how many times operator 1 returns its output to itself. (0-7 range)
|
||
- **Algorithm (AL)**: Determines how operators are connected to each other. (0-1 range and OPL1 and OPL2, 0-3 range on OPL3 4op mode)
|
||
- Left-click pops up a small "operators changes with volume?" dialog where each operator can be toggled to scale with volume level.
|
||
- Right-click to switch to a preview display of the waveform generated on a new note:
|
||
- Left-click restarts the preview.
|
||
- Middle-click pauses and unpauses the preview.
|
||
- Right-click returns to algorithm view.
|
||
|
||
- **4-op**: Enables 4-operator FM instrument editor mode (ONLY ON OPL3)
|
||
- **Drums**: Enables OPL drum mode editor
|
||
|
||
These apply to each operator:
|
||
- The crossed-arrows button can be dragged to rearrange operators.
|
||
- The **OP1**, **OP2**, **OP3**, and **OP4** buttons enable or disable those operators.
|
||
- **Amplitude Modulation (AM)**: Makes the operator affected by LFO tremolo.
|
||
- **Sustain flag (SUS)**: When enabled, value of Sustain Level is in effect.
|
||
- **Attack Rate (AR)**: determines the rising time for the sound. The bigger the value, the faster the attack. (0-15 range)
|
||
- **Decay Rate (DR)**: Determines the diminishing time for the sound. The higher the value, the shorter the decay. It's the initial amplitude decay rate. (0-315 range)
|
||
- **Sustain Level (SL)**: Determines the point at which the sound ceases to decay and changes to a sound having a constant level. The sustain level is expressed as a fraction of the maximum level. (0-15 range)
|
||
- **Release Rate (RR)**: Determines the rate at which the sound disappears after KEY-OFF. The higher the value, the shorter the release. (0-15 range)
|
||
- **Total Level (TL)**: Represents the envelope’s highest amplitude, with 0 being the largest and 63 (decimal) the smallest. A change of one unit is about 0.75 dB.
|
||
|
||
|
||
|
||
- **Envelope Scale (KSR)**: Also known as "Key Scale". Determines the degree to which the envelope execution speed increases according to the pitch.
|
||
- **Frequency Multiplier (MULT)**: Determines the operator frequency in relation to the pitch. (0-10, 12, 15 range)
|
||
- **Waveform select (WS)**: Changes the waveform generated by oscillator (OPL2 and OPL3 only, 0-7 range)
|
||
- **Pitch Modulation (VIB)**: Makes the operator affected by LFO vibrato.
|
||
|
||
## macros
|
||
|
||
Macros define the sequence of values passed to the given parameter. Via macro, along with the previously mentioned parameters, the following can be controlled:
|
||
|
||
## FM Macros
|
||
|
||
All parameters are listed above.
|
||
|
||
## OP1-OP4 Macros
|
||
|
||
All parameters are listed above.
|
||
|
||
## Macros
|
||
|
||
- **Arpeggio**: Pitch change sequence in semitones.
|
||
- **Panning**: toggles output on left and right channels. (OPL3 only!)
|
||
- **Pitch**: fine pitch.
|
||
- **Relative**: pitch changes are relative to the current pitch, not the note's base pitch.
|
||
- **Phase Reset**: Restarts all operators and resets the waveform to its start. Effectively the same as a `0Cxx` retrigger.
|
||
|
||
|
||
# links
|
||
|
||
[FM instrument tutorial](https://www.youtube.com/watch?v=wS8edjurjDw): A great starting point to learn how create and work with FM sounds. This was made for DefleMask, but all the same principles apply.
|